An accurate modal superposition method for calculating frequency response function of viscoelastically damped structures 粘彈阻尼結構頻響函數計算的高精度模態展開法
Firstly , with the curvature modal superposition method , the dynamic stress responses is calculated 首先,應用有限元方法,基于曲率模態疊加原理計算曲率,進而計算應變、應力。
Multi - flexible body dynamics is introduced into crankshaft computing , and diesel engine crankshaft dynamics simulation model is established combined with finite element method and modal superposition method 摘要將多柔體動力學方法引入到曲軸計算中,并結合有限元法和模態疊加法建立柴油機曲軸動力學仿真模型。
It spends much time to make an analysis of dynamic response and sensitivities with modal superposition method , and it reduces the efficiency of dynamic optimization design via this method 在動力優化過程中,采用常規的振型疊加法作一次動力響應及其敏度分析會耗費大量計算時間,這樣大大降低了動力優化設計的求解效率。
The seism response analysis of aqueduct bridge is analyzed with modal superposition method based on response spectrum which participant mode of vibration chooses the former 1 0 steps and combinatorial method was srss 渡槽的地震反應分析采用振型分解反應譜法,參與振型取前10階,組合方法用srss法,求得結構的地震作用效應。
In the chapter 2 , based on elastic mechanics and variation principle , the fundamental and process of static and dynamic fem is presented , placing special emphasis on the modal superposition method 第二章根據彈性力學和變分原理,系統總結了有限元法求解靜力學、動力學問題(包括特征值、動力響應問題等)的基本原理和步驟,并重點對模態疊加法求解動力,響應問題作了闡述。
Abstract : according to the deep analysis of the typical punching process , the loading charts and the amplitude - frequency curves of straight side cnc turret press frame are obtained . in the end the dynamic response of a typical process is calculated using modal superposition method by fem software marc and the static and dynamic stress of some nodes is compared as well 文摘:根據板料沖裁時的工作負荷圖確定了數控回轉頭壓力機的動載荷譜,并通過傅立葉展開,獲得了壓力機的幅頻譜,最后通過marc軟件采用模態疊加法計算了典型沖裁時機身的動態響應,分析了其動態特性,并對特征點的動靜態應力進行了比較。